How To Install Blade On Dewalt 20v Circular Saw

Equally an Amazon Associate we earn from qualifying purchases.

Designed for highly professional and extensive constructional works, Dewalt saw blades take an exclusive patent-pending pattern that makes them quite resilient and long-lasting.

Although not oftentimes, you will have to change the bract once in a blue moon to maintain the saw'southward efficiency. Therefore, you must learn how to change blade on Dewalt round saw.

Contents

• How To Change Blade On Dewalt Circular Saw
  • Footstep #1: Cut Off the Ability Supply
  • Step #2: Place the Saw on a Secure Platform
  • Stride #3: Press and Enable the Arbor Lock
  • Step #four: Rotate the Bract
  • Step #5: Press the Blade On A Wooden Platform
  • Step #6: Loosen the Basics
  • Stride #seven: Depress the Arbor Button
  • Step #8: Slide the New Bract into the Arbor
  • Pace #9: Screw the Nut Back
  • Stride #10: Do A Check-Up Run
• Often Asked Questions
  • What Dewalt Round Blade Size Practise I Demand?
  • What Types of Dewalt Round Saw Blades are Available?
  • Do Y'all Demand to Clean a New Dewalt Circular Saw Blade?
• Conclusion

How To Change Blade On Dewalt Circular Saw

Changing the bract of a Dewalt circular saw may seem like a hefty chore; however, you can easily supersede them past following these hassle-gratis steps.

Footstep #1: Cut Off the Power Supply

Usually, circular saw blades are powered by electricity, merely they are battery-operated in some cases.

In both situations, the first step to ensure prophylactic and sound removal is to switch off the electricity supply and remove all the cells of the high-power bombardment to prevent any mishaps.

Furthermore, gather a hammer, two pieces of forest, and a hex wrench or simple wrench before proceeding to the next step.

—

Warning!

As you're dealing with a loftier range of charged structure equipment here, it is crucial to follow all safety guidelines regarding the power supply.

—

Step #ii: Place the Saw on a Secure Platform

After cutting off the power from the saw blade, put information technology over a safe and fifty-fifty surface earlier removing the blade guard.

One time the saw is lying undisturbed, you lot can hands pull back the blade guard leaving the blade exposed.

Conduct in mind that even if the blade has get former, rusty, and blunt, it may still be hazardous when handled hastily. Take good care of the whole of the edge, removing the guard.

Step #three: Press and Enable the Arbor Lock

After exposing the edge of the blade, press the arbor lock situated at the acme of the housing. This volition enable you to lock the bract in place when you consummate the adjacent step.

Pace #4: Rotate the Bract

Keep the blade rotating until the arbor lock is installed correctly and it stops turning further. If your bract lacks the arbor lock, you need non worry about this pace since the next ane will ensure your prophylactic.

Step #5: Press the Bract On A Wooden Platform

Lastly, press this blade to a hard wooded surface so that the removal becomes easy.

The pressing adds the extra pressure level and support needed for the hassle-complimentary loosening of nuts and bolts.

Step #half dozen: Loosen the Nuts

Put your wrench onto the arbor nut. If your saw is channeled using a batter, the loosening slot can only exist accessed using a hex wrench as the arbor contains a space for this detail wrench.

One time situated, continue on rotating the wrench up until the bolts come undone. The direction followed here must be counterclockwise.

The best-suited wrench for your saw comes along with the Dewalt round bract saw in the package.

Footstep #7: Depress the Arbor Button

Keeping the arbor button depressed is quite essential while unscrewing the nut. Press information technology, and the entire blade comes off its shaft.

If the switch is absent in any models, just pressing the saw down would prepare it.

Footstep #8: Slide the New Bract into the Arbor

Once the old blade is down and unscrewed, have a new and precipitous blade. Slide this new blade over the arbor, ensuring that you've installed information technology according to the instructions on the packaging.

—

Tip

You have to pick the centre of the blade out to fix it over the arbor. For doing then, advisedly brand a hole using a hammer by punching over and over.

—

Step #9: Screw the Nut Dorsum

Situate the nut where you tightened it earlier. Utilize the aforementioned wrench used while unscrewing and finally plug in the bombardment or ability supply.

Exercise non tighten the nut as well much; it might get hard to remove when replacing the new bract after its due course.

Step #10: Practice A Cheque-Up Run

After plugging the blade into the power supply, it is vital to plug the cords into the sockets to cheque its performance.

If the blade is running and making a wheezing metallic sound, it ensures that it is fixed appropriately.

—

Alert!

As a high charge would exist flowing back again into your saw bract, please follow all the electricity rubber guidelines while running the cheque-up. Wear goggles, gloves, and other safety gear.

—

While reading the aforementioned stride-by-step procedure may guide your way through the entire process, it would also be helpful to go through a video to get more than precise ideas.

Here is one of the many helpful videos that will assist you learn how to alter the blade on the Dewalt circular saw.

Frequently Asked Questions

What Dewalt Round Blade Size Do I Need?

You need to use the proper size blade for your Dewalt round saw, which should be provided to you lot on the saw. The most common Dewalt blade sizes are half dozen.five″ and seven.25″.

Another important thing affecting the size is the arbor, the middle pigsty of the blade's bore. The new blade will only fit in the saw's shaft if it has the same diameter as the arbor.

What Types of Dewalt Circular Saw Blades are Available?

The three most common types of Dewalt round saw blades are rip blades, crosscut blades, and combination blades. Dewalt besides makes specialty blades for specific types of cuts or materials.

Do You Need to Clean a New Dewalt Round Saw Blade?

When you get a brand new circular saw bract, you lot do non demand to make clean it prior to install. Yet, over time, your bract will need to be cleaned, every bit they develop a lot of grease and build up while cutting.

Circular blades may be super handy, but they are also the most incredible home to all $.25, pieces, and wood chipped during the cutting work. These chips and cuts are the main reason behind the excessive, blunt edges, even in the new blades.

Hither is a quick way to maintain your round saw bract yourself and come across the dirt and accumulation go away in a swiss and flick.

Conclusion

Dewalt circular saw blades are reputed in the field of structure jobs and cutting businesses. What makes them even more than efficient and prominent is their easy replacement once they are blunt, dirty, and too old to piece of work.

Moreover, a leading proper name like Dewalt comes with the security that a newly installed blade will work unbothered for a longer span, thereby adding value to your investment. These blades, one time installed, tin can withstand all extreme usages and weather far longer than their local counterparts.

With this guide, you lot can replace all types of Dewalt circular saw blades.

Source: https://sawshub.com/how-to-change-blade-dewalt-circular-saw/

Posted by: clarkbeids1938.blogspot.com

Share this post